Engineering guide

Metal sheet, RCC, ground mount or carport: choosing the installation

What each structure asks of your site, what to check before you commit, and where battery storage fits.

Short answer

Use what your site already has. A sound metal sheet roof is usually the quickest to build on. A flat RCC roof works but needs more area per kWp. Spare land inside the boundary suits a ground mount, and parking suits a carport. Many factories combine two types, and a structural check of each roof comes before any design.

Key takeaways

  • Start with what the site already has: roof area and condition, free land inside the boundary, parking. Most factories use more than one type.
  • A roof must outlive the plant’s first decades, or be repaired first. Check remaining roof life before anything else.
  • Flat RCC roofs need more area per kWp than metal sheet roofs, because tilted rows must be spaced to avoid shading each other.
  • Battery storage is an add-on to any installation type. It earns its place on demand charges and peak tariffs.

Four structures compared: what each needs and what to watch

The panels are much the same whatever you mount them on. What changes is the structure, what the site must be able to carry, how much area each kWp needs and what can go wrong over 25 years.

General guide. A check of your own site settles what each roof or plot can take.
TypeBest whenCheck firstWatch for
Metal sheet roofLarge sheds with sound sheets and plenty of life leftSheet condition, profile and purlin spacingRoof-sheet warranty, wind uplift, skylights
RCC roofFlat concrete roofs with spare slab capacitySlab load capacity and waterproofingRow shading, roof access for other services
Ground mountFree land inside the boundary near your connectionSoil, drainage and future building plansVegetation, flooding, security
CarportParking is the space you haveLayout of bays and driveways, vehicle heightsHigher structure cost per kWp

Metal sheet roofs: quickest to build, if the sheets have life left

The most common factory roof, and usually the quickest to build on. See our page on rooftop solar for metal sheet roofs. The plant follows the roof’s slope, so there is no row spacing to lose. The structure is fixed through the sheet in many cases; where you want a zero-leakage roof, we use non-penetrating adhesive or clamp mounting chosen for the sheet profile. Either way it is designed to comply with OEM installation guidelines, on structures designed for the wind speed under IS 875.

Three checks come first. The sheets must have enough life left to carry the plant for decades, or be replaced before installation. The sheet profile (trapezoidal or standing seam) decides which clamps or fixings suit it. And the purlins and rafters must carry the extra load, which a structural engineer should confirm (we do not assess roof strength ourselves, but can refer one). Skylights, ridge vents and walkways for maintenance need to be planned into the layout, not worked around later.

RCC roofs: check slab load and leave room between rows

RCC (reinforced cement concrete) roofs are flat, and they take tilted module rows on ballasted or anchored structures. Ballast leaves the waterproofing unbroken but adds dead load, so the slab’s spare capacity has to be confirmed by a structural check. Anchors take less weight but pass through the membrane, so each one must be sealed. Rows must be spaced so they do not shade each other in winter, which is why an RCC roof needs more area per kWp than a metal one. Walkways and safety lines are mandatory in every layout we design.

Ground mount: spare land inside your boundary

A ground-mount plant uses spare land inside your boundary. It suits factories whose daytime load is larger than their roofs can serve, or whose roofs cannot take more load. The tilt and orientation can be set for the best yield, and there is no roof to protect. In exchange it needs land you will not want for a building, a check on soil and drainage, fencing, and vegetation control for the life of the plant. Inside your boundary, it connects behind your meter like a rooftop plant.

Carports: when parking is your open space

A carport puts the plant over parking, shading vehicles while it generates, and it can be built ready for EV charging. The steel structure costs more per kWp than a roof mount, so carports usually make sense where parking is the main open space, or where shade for vehicles and charging points add value of their own. Vehicle heights, bay layout and fire access shape the design.

How much area a plant needs

A rough first check on whether your site can hold a meaningful plant needs only module dimensions:

Illustrative exampleModule area per kWp

Assumptions

  • A typical 580 Wp module measuring about 2.6 m²
Module area per kWp
about 4.5 m²
Module area for 1,000 kWp
about 4,500 m²

That is modules alone. Walkways, edge setbacks, skylights and, on flat roofs, the gaps between tilted rows add to it; the layout decides the final figure.

Assumed figures to show the method. Not a quote and not a result from any Adhvanik plant.

Where battery storage fits: demand charges and peak hours

A battery energy storage system (BESS) sits alongside any of these. For a factory it does three jobs: shaving peaks to cut demand charges, shifting energy into peak-rate hours, and firming up supply alongside solar. It earns its place where demand charges are a large part of the bill, or where time-of-day tariffs open a wide gap between peak and other hours. The 2023 amendment to the Electricity (Rights of Consumers) Rules sets peak tariffs for commercial and industrial consumers at not less than 1.2 times the normal tariff, which is the kind of spread storage works on. Whether it pays at your site depends on your meter data, so model it rather than assume it.

Four questions to put to any vendor about your roof

  1. Have you checked the remaining life of my roof, and what happens if it needs work during the plant’s life?

    Removing and refitting a plant for roof repairs is expensive and needs planning.

  2. Which mounting method do you propose for my roof, and how does it affect the roof warranty?

    Ask for it in writing against your sheet or membrane make.

  3. What structural checks have you done, and who signs them?

    Load and wind calculations should come from a qualified engineer, not a standard drawing.

  4. How will my team reach and maintain the roof after installation?

    Walkways and lifelines are part of the design, not an extra.

Our free 7-day feasibility study includes a roof feasibility check and the area available for each roof or plot you offer.

Sources

Policy and tax rules change. Facts below were checked in Nov 2026; confirm the version in force for your state and tax year before you sign.

  1. Electricity (Rights of Consumers) Amendment Rules, 2023: rule 8A, Time of Day tariff (opens in a new tab). peak and solar-hour pricing that shapes storage economics
  2. Global Solar Atlas (World Bank Group / Solargis): PV output and optimum tilt by location (opens in a new tab)

Common questions

Mixed roofs, old sheets, spare land and carports

Short answers. The working is in the guide above.

Get a free feasibility study
Can one plant combine roof types?

Yes. Many factories have metal sheet sheds and RCC buildings side by side, and a single plant can span both, feeding the same connection. Each roof gets its own structure design.

Our metal roof is old. Should we replace it first?

If the sheets are near the end of their life, usually yes. Removing and refitting a plant to replace a roof later costs more than doing the roof first.

Does a ground-mount plant need a separate approval?

A plant inside your boundary feeding your own connection is normally treated like a rooftop plant for connection purposes, but local building, land-use and DISCOM rules apply. Check them early.

Are carports worth it on cost alone?

Rarely on cost alone, because the steel structure costs more per kWp than a roof mount. They make sense where parking is the space you have, or where shade and EV charging add value.

Free feasibility study

Get a roof feasibility check for your site

The feasibility study is free, takes 7 days and carries no commitment. An engineer replies within 48 hours.

What the study covers

  • Financial ROI sheet based on a preliminary design
  • Policy check for your state and connection
  • Roof feasibility and the area available for installation
Call us+91 22 4618 3484Get a free feasibility study